Item MPN | Question | Answer |
| T3-Series-Rack | Weight capacity? | 4,400 LB's Rack Capacit, 1,100 Rackable Capacity |
| T3-Series-Rack | Dimensions? | 2"3" uprights, Depth= 24", 36", Inside Width= 42", Heights= 82, 91" |
| T3-Series-Rack | Hole size and spacing? | 11/16" , 3" spacing |
| T3-Series-Rack | Can the short extension work with the Tall rack? | Yes |
| T3-Series-Rack | Material? | 11- Gauge Steel |
| T-3-POWER-RACK | What are the overall width and depth of the T-3 Short 36 rack, excluding the foot plates? | The rack measures approximately 42 1/8 inches wide and 42 inches deep, excluding the foot plates. |
| T3-Series Rack | Can a T-3 Short 36" rack with a 24" extension accommodate simultaneous use for squats, benching, and lat workouts? | Yes, adding the 24" extension will provide enough space to allow for benching and lat workouts inside the rack while still leaving adequate room at the front for squats and spotter access. |
| T3-Series Rack | Is the pull up bar height adjustable? | Yes the Pull-Up bar height can be adjusted |
| T3-Series Rack | Can power racks be used or stored outdoors? | Power racks are not designed for outdoor use or exposure to the elements. However, if kept in a covered area, they may be used outdoors with proper maintenance—such as regularly wiping off moisture and addressing any scratches to prevent surface rust. |
| T3-Series Rack | Are the round safety bars on the T-3 rack as strong as other safety catches, and will they bend over time? | Yes, the round safety bars provide comparable strength to other safety mechanisms, such as flip-down safeties. They are designed to handle heavy loads, and there have been no known issues with them bending over time under normal use. |
| T3-Series Rack | Can the lat tower attachment be used together with a pull-up cage attachment on a T-3 rack? | Yes, the lat tower mounts to the back of the rack, while pull-up attachments install on the front or top. This setup allows both to be used without any clearance issues. |
| T3-Series Rack | What is the spacing between the holes on the jammer arms? | The holes are spaced 6 inches center to center. |
| T3-Series Rack | What is the hole spacing on the T-3 Series Short Power Rack (24" depth)? | The upper and lower holes are spaced 2 inches center to center, while the middle (bench area) holes are 1 inch center to center. |
| T3-Series Rack | What is the height to the top of the side cross members? | The top of the side bracing is approximately 78 inches high. |
| T3-Series Rack | How can I improve stability if I don’t want to bolt the rack down but plan to use attachments like pulley systems or lever arms? | Adding weight plate holders lower on the uprights can help improve overall stability. |
| T3-Series Rack | What pulley system is compatible with the T-3 short rack for high and low pulley movements? | The compatible pulley system is MPN: TRIPLLY. |
| T3-Series Rack | Do T-3 racks have 1-inch hole spacing, and will spotter arms fit inside a 24" extension? | No, T-3 uprights have 2-inch center-to-center hole spacing. Spotter arms will not fit inside the 24" extension, as the spotter arms themselves are 24 inches long. |
| T3-Series Rack | What is the diameter of the holes in the tubing? | The upright holes measure approximately 11/16 inches in diameter for X-2, T-3, and X-3 racks. |
| T3-Series Rack | What is the spacing of the mounting holes on the feet for a T-3 Short 36" rack? | The mounting hole spacing (center to center) is approximately 50 inches wide and 39 inches deep. |
| T3-Series Rack | Can the lat tower be moved to a 10" extension on a T-3 rack? | Yes, the lat tower can be attached to the 10" extension. |
Support Center