Item MPN | Item SKU | Question | Answer |
| T2LATTWR_BASE | 401199 | What are the cable dimensions? | 144-in cable length | 0.225-in cable diameter. |
| PPLDM | 400211 | What is the inside diameter of the safety bar? | The safety bars on the T-2 are 1" in diameter. The Sleeve opening on the attachment is 2" |
| T2SA | 401090 | How far apart are the center of the two pins? | 200mm |
| T2EXT83 T2EXT71 T2EXT71_NVY T2EXT71_RED T2EXT83_NVY T2EXT83_RED | 401210 401209 402062 402061 402064 402063 | Is there a torque recommendation? | We do not have any torque specs for our Power Racks. We suggest tightening the nut until its snug. |
| T2RACK83_BK | 401836 | How high off of the ground is the top hole for the J-hooks? | They can be placed on the distance between the highest point and the ground, which is 1593.5mm. |
| T2-SERIES-RACK | T2-SERIES | Material? | 12 Gauge Steel | Powder-coated |
| BRANCHOR | 401460 | How can I safely attach a battle rope to my ceiling? Can I use one anchor on the ceiling and another on the wall without knotting the rope? | We recommend using the Battle Rope Ceiling Anchor (SKU: 410565). You can also use the Anchor Strap (SKU: 410562) to attach to the ceiling anchor. This method avoids knotting and secures the rope safely. |
| PWR1-PWR2 | 400100 | What size wrenches do I need to assemble a T-2 power rack? | You will need an 18 mm wrench or socket. |
| PWR1-PWR2 | 400100 | What is the proper order for bolt, washer, and nut during assembly? | The correct order is: Bolt → Washer → Nut. |
| PWR1-PWR2 | 400100 | My T-2 rack has been outside and is getting rusty. Will this affect structural integrity? | Check for surface rust regularly. Remove any rust by sanding and applying Rust-Oleum. Minor surface rust generally does not affect structural integrity, but monitor areas as your lifting loads increase. |
| PWR1-PWR2 | 400100 | Why do the instructions call for 24 flat washers when only 20 were included? | Eight M12x75 carriage bolts with square necks do not require washers, which accounts for the difference. |
| PWR1-PWR2 | 400100 | Can I attach a pivoting boxing reflex trainer to a T-2 rack? | No, the T-2 does not have side holes and the hardware does not match the T-3, so this attachment is not compatible. |
| PWR1-PWR2 | 400100 | Is the hole spacing on the T-2 rack true 2-inch spacing? | Yes, vertical holes are 2 inches on center, with some sections between holes measuring 1 inch. |
| PWR1-PWR2 & SHPWR1-SHPWR2 | 400100 | What is the height of the lowest and highest holes on the T-2 and T-2 Short racks? | This data is not currently available. |
| PWR1-PWR2 / SHPWR1-SHPWR2 | 400100 | Can I safely keep a T-2 Short Rack outdoors or in a shed? | Power racks are not meant for outdoor use. Storing in a shed is acceptable as long as it is protected from the elements. |
| PWR1-PWR2 and SHPWR1-SHPWR2 | 400100 | What is the vertical hole spacing for the T-2 rack? | 2 inches center to center. |
| PWR1-PWR2-PWRDIP | 400100 | I’m having trouble assembling a product because there’s no hole in the bolt. | Please provide additional details, as the question is unclear. |
| SHPWR1-SHPWR2 | 400160 | Is the T-2 rack made of 14-gauge steel? Can I get 11-gauge steel instead? | T-2 racks are 12-gauge steel. T-3, X-3, and Titan Series racks use 11-gauge steel. |
| SHPWR1-SHPWR2 | 400160 | What is the spacing of the two mounting holes on the back brace at the very top of the T-2 rack? | The holes are 4 inches center to center. |
| SHPWR1-SHPWR2 | 400160 | How should I space washers when instructed to use 8 bolts, 8 nuts, and 4 washers? | Eight M12x75 carriage bolts with square necks do not require washers, so the four washers are only needed for other specific bolts. |
| SHPWR1-SHPWR2 | 400160 | My T-2 Short Rack wobbles on a level floor. How can I stabilize it? | You can add weight to the rear weight post or secure the rack where the four uprights mount into the lower side bracings. |
| SHPWR1-SHPWR2 | 400160 | Can a T-2 Short Rack be disassembled and reassembled frequently for moving? | Yes, it can be disassembled and reassembled. For frequent moves, consider the X-2, which has welded uprights and side bracings; only pull-up bars need to be bolted. |
| SHPWR1-SHPWR2 | 400160 | Are there any compatible attachments for the T-2 rack, such as spotter arms, safety straps, leg press, or lat tower? | Spotter arms, safety straps, and leg press are compatible. The lat tower will not fit the T-2 because it lacks the required side holes for installation. |
Support Center