Item MPN | Item SKU | Question | Answer |
| JHOOK_T3 | 401348 | What is the pin size for this item? | 5/8" |
| 24T3STRAPv2 | 400689 | What size are the loops? | 4 inch loops |
| 24FDWNS_T3 | 401345 | Why is there a gap between the accessory and the upright? | The gap is part of the design. If there was not a gap between the upright and the safety bar, you would not be able to install the bar or flip it down. |
| SPHPUBAR_T3X3TS | 401345 | How big are the holes on the mounting bracket? | 11/16. |
| RCKSTP_T3 | 401353 | What is the weight capacity? | 550 pounds |
| RCKSTP_T4 | 401353 | What is the diameter of this quick pin? | 5/8" |
| XDIP_T3 | 401343 | What is the diameter of the pin. | 5/8" |
| T3XDIP | 400132 | Do you offer attachments for the T-3 Series Tall Folding Power Rack (41" Depth | V2)?
| Yes, there are several compatible attachments available; however, not all attachments will work with folding racks. The X Dip Bar is not compatible with folding power racks. However, the T-3 Y Dip Bar Attachment is compatible and can be used. Customers have successfully used attachments such as Lever Arms, Spotter Arms, and Monolifts with folding power racks. |
| T3YDIP | 400132 | Is the Y Dip bar compatible with T-3 Wall Mounted Rack? | Yes it is compatible |
| TRIPLLY | 400064 | What are the dimensions of the long arm for the Tricep and Lat Pulley System (T-3), and will it interfere with a multi-grip pull-up bar on a 24" rack? | The pulley system mounts to the sides of the rack and is not expected to interfere with a multi-grip pull-up bar. The mounting bracket is approximately 150 mm wide, and the holes are spaced 100 mm apart, so at least this amount of space is required on the 24" side bracing. |
| TRIPLLY-LOWPLLY | 400068 | (1) Can a pulley system be attached to folding racks? (2) Can non-folding power racks support an adjustable pull-up bar? (3) What are the installation requirements for folding racks vs. non-folding racks (e.g., wall-mounted vs. floor-mounted)? (4) Are both folding and non-folding racks compatible with TRX systems? (4) What size Olympic barbell is required for use with a squat rack? | (1) No, the pulley system is not designed to be installed on folding racks. (2) The racks are not designed for wall-mounted pull-up bars. However, the pull-up bars included with PWR racks are adjustable. (3) Folding racks must be anchored to wall studs, and using stringers is recommended for added support. Non-folding racks need to be bolted to the floor, except for the X-3 Flat Foot style. (4) Yes, but it is strongly recommended to anchor the stringers to at least four studs to properly distribute the load. (5) A standard 86-inch Olympic barbell is recommended. |
| TRIPLLY-LOWPLLY | 400068 | Would the complete pulley system fit on the 10inch expansion for the T-3 short rack or the 24 expansion? | The Pulley System would work on either extensions. |
| TRIPLLY-LOWPLLY | 400068 | How to lubricate? | Recommend using a Silicone based spray lubricant on the pulleys. |
| TRIPLLY-LOWPLLY | 400068 | What is the exact diameter of the cable, and does the .225" measurement refer to the full cable including the plastic coating or just the internal metal wire? | The Cables diameter with the sheeting is 5.715mm (0.225") |
| T3WRLR | 400644 | What is the diameter of the pin for the jhook bracket? | 17mm |
Support Center