| Item MPN | Item SKU | Question | Answer |
| CMMGBAR | 400580 | Do you have installation instructions? | We currently do not have a installation manual. |
| CMMGBAR | 400580 | How far apart are the 2 bolt holes that mount to ceiling? | 2" w x 5 1/8" L. |
| CMMGBAR | 400580 | How wide is the rectangle brace those holes are on? | 4" bolt hole spacing (C to C) |
| CMMGBAR | 400580 | Does the pull up bar come with wood anchors? | The mounting hardware that is supplied is for anchoring into concrete. We recommend purchasing Wood Anchors locally. |
| LWPUB | 400501 | Do you have anchors and screws available for drywall and stud mounting instead of the concrete anchors that came with the pull-up bar? | Unfortunately we do not offer any other type of Anchors. |
| LWPUB | 400501 | How do you mount the LW Pull up Bar? | The best and most secure way to install the Pull-Up Bar is to first anchor wooden stringers into the wall studs, and then mount the Pull-Up Bar onto the stringers. This method helps distribute the weight more evenly and provides a more secure installation. |
| PullUpBar1422 | 400513 | What is the weight capacity of this bar? | As long as the item is mounted properly, it can support up to 400 lbs. However, if the item is mounted incorrectly, it may not safely support any weight. |
| PullUpBar1422 | 400513 | How to install bar to a concrete wall? | Please be sure to use Concrete/Masonry Anchors and not Wood Anchors. |
| PullUpBar1422 | 400513 | What is your recommendation for smoothing the bar out? | You can use 80 grit sandpaper or have wrapped the bar with lifting tape |
| PullUpBar1422 | 400513 | What is the vertical distance between all the screws? | Top 2 screws 3 57/64" Top screw to bottom 20 5/8" |
| PullUpBar1422 | 400513 | How to mount adjustable pull up bar to wall? | We always suggest using stringers whenever installing an item onto a wall for better weight distribution and strength. |
| PullUpBarHD | 400512 | What is the recommended hardware for this item? | We recommend using 3/8" x 3" Lag bolts |
| PullUpBarHD | 400512 | Can you mount this pull up bar on dry wall? | All homes will have Studs spaced either 16 or 24 inches apart. You will need to ancor the pull-up bar to Studs. If you anchor the brackets to just the drywall, the pull-up bar would most definitely be pulled away and cause damage to your drywall. |
| PullUpBarHD | 400512 | What size of the hex bolt do I need? | 3/8 x 4" long lag bolts |
| PullUpBarHD | 400512 | What is the size of the top screw? | M12x30 |
| PullUpBarHD | 400512 | Should the pull up bar only have 1 drill hole? | The Pull-up Bar should only have one hole. The hole keeps the Bar from sliding out. |
| PullUpBarHD | 400512 | Are the plastic anchors included in the install kit intended for drywall installation or for mounting into wooden studs? | The plastic anchor sleeves are for both applications but we would suggest using Lag Bolts |
| PullUpBarHD | 400512 | Does the bracket width exceed 1.5"? | The bracket width does slightly exceed 1.5". We suggest mounting stringers to the rafters and than mounting the pull-up bar to the stringers. That will help distribute the weight. |
| PULLUPBARHD | 400510 | Only one side of the bar has a hole and not the other side. Is it missing a hole to allow mounting? | This hole on the bar is a process hole used for spraying, not for installation. |
| SMPUB_S | 400507 | What is the bolt size for the pull up bar? | 3/8" x 2.5" Anchor Bolts |
| SMPUB_S | 400507 | What screws to use to install the pull bar into dry wall? | 3/8" x 3" Wood Lag Screws |
| smpub_S | 400507 | Can it be hung on an angles ceiling? | As long as it's attached to studs you can, product will of course be affected by the angle |
| SMPUB_S | 400507 | What are the joist span requirements? | 50" |
| SPUB | 401139 | What is the diameter of the part listed as HITCH PIN Φ16*125 | 15.9mm. |
Support Center